Cool Power (30 Gal.Drum) *Nufa

Active Ingredients

EPA REG. NO.: 228-317
ACTIVE INGR.: MCPA (56.14%), triclopyr (5.0%), dicamba (3.6%)
FORMULATION: liquid
CHEM. FAMILY: phenoxy, pyridine, benzoic acid
HRAC NUMBER: 4
SIGNAL WORD: caution
RESTRICTED: no
PACKAGE SIZE: 2 x 2.5 gal, 30 gal

KEY USES

Cemeteries
Golf courses (fairways, aprons, tees and roughs)
Lawns
Non-crop areas
Turf (not pasture)
Parks
KEY WEEDS CONTROLLED

Black medic
Buckhorn
Chickweed
Clover
Dandelion
Dock
English daisy
Florida pusley
Ground ivy
Healall
Henbit
Knotweed
Kochia
Lespedeza
Mallow
Morningglory
Oxalis
Pigweed
Plantain
Ragweed
Sowthistle
Spurge
Thistle
Toadflax
Veronica
Wild geranium
Wild violet
Woodsorrel
Yarrow
See product label for complete list

PREMIUM COOL WEATHER WEED CONTROL

Premium ester formulation for cool-weather weed control
Can be used in 2,4-D sensitive areas
Maximum weed control power in early spring and fall extends spray season
Contains triclopyr to control hard-to-kill weeds like ground ivy and wild violet
Can be used for spot treatment under warmer conditions
Tank-mix compatible with most liquid fertilizers and iron*
*Compatibility test required
USE SUMMARY
ORNAMENTAL LAWNS AND TURF
Apply Cool Power� Selective Herbicide at the rate of 2-1/2 to 3-1/2 pints in 20 to 240 gals of water per acre (0.91 to 1.29 fl oz in 1/2 to 5.5 gals of water per 1,000 sq ft) to control weeds growing in turf planted to bluegrass, fescue, rye, bent (excluding golf greens and tees), bahia, bermuda, and zoysia.

When treating warm season turf that is completely dormant, the higher rates may be used. When treating warm season turf that is actively growing, use a lower rate. Avoid applications to warm season turf during transition from dormancy to green-up or green-up to dormancy.

Herbi� Controlled Droplet Applicator: Add 1-2/3 to 2-1/2 pints of Cool Power to the 5 pint Herbi bottle, then fill with water to make 5 pints of mixture or substitute 1/2 pint of a surfactant for water while agitating the solution.

While walking at approximately 1 pace (3 feet) per second, spray entire contents over 33,000 sq ft (3/4 of an acre). Do not overlap (double coverage) at edge of spray patterns. Reduced rates (use 1/2 of rate shown above) of Cool Power must be applied when grass is stressed from heat, drought, etc.

Controlled Droplet Applicators � (CDA), Atomizers, and Spinning Disk Applicators: Use Cool Power at 2-1/2 to 3-1/2 pints per acre (0.9 to 1.25 fl oz per 1,000 sq ft) in sufficient water to assure coverage (1 to 4 gals of water per acre is normal for this type of equipment).

NOTE: For all grasses (1) Do not overlap spray patterns; (2) Use reduced rates if grass is stressed from heat, drought, etc.; and (3) Follow CDA equipment spray instructions.

OTHER NON-CROP AREAS

Roadsides (Including Aprons and Guard Rails), Rights-of-Way, and Other Similar Non-Crop Areas: For the control of broadleaf weeds, mix at a rate of 1/4 to 3/4 gal of Cool Power per 50 to 300 gals of water. This mixture will cover 43,500 sq ft. Thoroughly saturate all weeds with spray mixture. Apply any time between the time when plants come into full leaf (Spring) to when the plants begin to go dormant. Best results are obtained when weeds are young and actively growing. Do not cut weeds until herbicide has translocated throughout the plant causing root death. For small broadleaf weeds, use the lower rate. Heavy, dense stands require the higher rate of 3 oz of Cool Power per gal of water and spray to thoroughly wet all foliage.

See product label for complete directions for use.